1954 Chevy (210) Belair
Condition: | Used |
Make: | Chevrolet |
Model: | Bel Air/150/210 |
Type: | Sedan |
Trim: | 210 |
Year: | 1954 |
Mileage: | 2,200 |
Color: | Silver |
Engine: | 5.3l LS |
Cylinders: | 8 |
Fuel: | Gasoline |
Transmission: | Automatic |
Drive type: | RWD |
Interior color: | Blue/ White |
Vehicle Title: | Clear |
Item location: | Belle Chasse, Louisiana, United States |
Extras |
Listed by |
Private seller |
Description of 1954 Chevrolet Bel Air/150/210 210 |
|||
1954 Chevy 210 Belair condition: fair cylinders: 8 cylinders drive: rwd fuel: gas paint color: silver size: full-size title status: clean transmission: automatic type: sedan
Engine The engine in this car is anLS-series5.3-literLM7 from out of a 2004 Chevy Silverado. It's mountedwithsolid motor mounts from Dirty Dingo. Acustom-madeengine harness form PSI gives power to thestand-aloneengine managementsystem. Furthermore, the PCM has a custom tune to unlock all this 5.3L has tooffer from a stockmotor.Cold, denseair is stuffed into the motor through a custom ram air intake.Themotor is cooled by an aluminum three-core radiator with dual electric fans. The fans are programmed to come on at 190 and 195respectively.Finally, fuellines have been replaced with steel braided fuel lines. Transmission Power is transferred to the wheels through a 2004r transmission built by MonsterTransmission.Furthermore, Monster Transmission was verythoroughwith this custom build, for example, they required me to give them the engine size and horsepower,theweight of vehicle, tire size and rear axle ratio. Thus, whateverenhancementsthey recommendedI told them to throw it in there.This monster has an upgraded sun gear and friction plates, corvette servo, and a shift kit to make tires bark under hardacceleration. The transmission is held in place with a tubular transmission crossmember from Walton Fabrication.Finally, toshift herthroughgears a pro-ratchet shifter with reverse lockout was installed. Interior The interiorofthis vehicle is in greatcondition, for example, the seats have no wear, the ceiling liner is not falling and everything on the dash is there. However, the carpet is faded and worn.Furthermore,mostofthe door glass hascracks, and the windows need felt replaced. Keeping the interior looking as original aspossibleand bringing it into the future,Dakota Digital gauges were installed in the dash. Furthermore, the speedometer is registered through GPS(nocable to thetransmission), as a result, no matter what you change your tire size to the speedometer does not need to be adjusted. To help with theft, a key fob is needed on your person to activate the push button start. Suspension For starters,I had toget the Belair out of the sky, as a result, 2 coils were removed from the frontcoil springs for a2.5-inchdrop in the front. Thentherearhas 3-inchlowering blockswith air shocks installed to give it a smoother ridewhen the trunk isloadeddown,andthe family is crammed in the back seat, in addition to,stopthecar from bottoming out from all the weight in the rear. Brakes The go was upgraded, so the stop had to be upgraded. A front brake discconversionkitfromPerformance Online (POL)wasinstalled,thekit includeddrilled and slotted rotors. The rear drums wereadjustedand new wheel cylinders were installed.Furthermore, apowerbrake booster, dual master cylinder, and vacuum reservoir kits were installed to make this car stop like a modern vehicle. Thus, no more pumping brakes to stop.5-poundproportioning valve was installedin linefor the disc brakes and 10-pound proportioning valves were installed for the drum brakes in the rear. Finally,allbrake lines havebeenreplaced with steelbraided brake lines. Exterior Soon as I got this54 Belair in mygarage, itwas disassembled anda frame off restorationbegan. The only major cancer on the car wasthepassenger side rockerpanel. The rocker panel was cut out and a reproduction piece was welded in. Theentire undercarriagewas cleaned, treatedwithCoraseal, and a rubberized undercoating was applied. The firewall was moved back 4-inches to allow the 5.3Ltofit, as a result, you have a panel you can unboltfor maintenanceon the backof the engineif needed. Furthermore, all the body bolts and pads were replaced before the body was put back on theframethat was cleaned, treated and painted with Chassis Saver.I wanted a smoother look so after the chrome was removed theholeswere filled in. Uponthe completion of the bodywork,I applied Chassis Saver to deter the car from rusting until I decided to paint the car. The hood ornament was deleted and replaced with a bullnose clipthat givesthehood a clean look. I couldn't see 10yds ahead of me onanunlit road,sothehalogenheadlights werereplaced with L.E.D headlights. Furthermore, the parking andturnsignallightshave beenupgradedwithL.E.Dsas well.The faded hood and trunk emblems were replaced withexcellent reproduction pieces. Finally, the vacuumcontrolledwindshield wipers were replaced with a modern12-voltreproduction system. What needs to be Done Everything major has been done to this vehicle to make it drive and stop safely. However, there are several improvements I have not accomplished. The list is as follows: all 4 doors needweather-stripping,themajorityofthedoor glasshascracks and need to be replaced,sothe glass does not vibrate in the doorframethe window felt needs to be replaced,trunk needs weather-stripping, and it needs a paintjob. In addition, a couple ofthecreature comforts you can add is a radio, air conditioning, and seatbelts. |