1967 Chevrolet Camaro RS/SS Coupe 383 Stroker
Condition: | Used |
Make: | Chevrolet |
Model: | Camaro |
SubModel: | RS/SS |
Type: | Coupe |
Trim: | RS/SS |
Year: | 1967 |
Mileage: | 33559 |
VIN: | 124377N17311G |
Color: | Blue |
Engine: | 383 Stroker V8 |
Cylinders: | 8 |
Fuel: | Gasoline |
Transmission: | Manual |
Drive type: | RWD |
Interior color: | Blue |
Vehicle Title: | Clear |
Item location: | Keyport, New Jersey, United States |
Extras |
-- -- |
Listed by |
Private seller |
Description of 1967 Chevrolet Camaro RS/SS |
If you are looking for a real deal Camaro RS/SS then look no further. The pictures and the description will capture and highlight this exceptional Camaro as it rightly deserves. I purchased this from a gentleman who got this car from his father when he was a teenager. After many years of owning it he decided it was time to restore it. A professional shop restored the frame, body, new floors, and paint work. So I bought the camaro along with some new parts. Then in my shop I purchased all required remaining parts and completed the full 100% restoration as detailed below. All parts are brand new OER top of the line parts. This car is brand new in every aspect, very close to what rolled off the assembly line in 1967. We added power brakes for the safety factor and power steering to make driving it a whole lot better. If you are interested we invite you to come and inspect it in person or send a professional in to do so.
6 Custom Interior 37 Coupe Nor Norwood plant 72623 Sequence code 732 Custom Interior Z Bucket Seats F-F Marina Blue Top and Bottom E Tinted Glass 2LG Option Group: L 4 Speed G Console 3L RS Package 4P SS350 L-732 Custom Interior "Bright Blue" Gone is the stock 350 with 295hp. In place is a 383 stroker that cost over $11k to build. We had the engine builder purchase the best parts available and it shows in the way it runs and drives. 383 stroker was built by JTL then sent to RAZ Performance in Vineland NJ for head work and dyno tuning Dyno @ 464hp at 5500 rpm and 459 lbs torque at 4800 rpm Dyno run was at a very conservative rpm, Dyno spike at higher rpm showed 493 HP Scat forged rotating assembly 1-46017BE Lower end and complete rotating assembly balanced and blue printed Comp cam and Ultra Pro Magnum rockers 1.6 AFR heads 195 Street Eliminator, ports worked by RAZ performance Vintage 780 Holley worked by Phil, Custom Rebuilt Carbs, Middlesex, N.J. MSD ready to run distributor modified and set up by Raz Performance for this engine Eldelbrock Dual plane intake for up to 6,500 rpm Muncie M20 rebuilt with factory parts McLeod diaphragm clutch with SFI rated steel flywheel Original 12 bolt rear. 3.31 Posi Brand new balanced drive shaft, new slip yoke and U joints New aluminum 4 core radiator New Alternator, heater box, heater core and heater motor. All new pulleys, belts and battery.
Rear cover updated to Aluminum finned old school cover New power steering box, pump and lines. American Racing Torque Thrust Cooper radials front P215/70R15 rear 255/60R15 $500 deposit is required within 24 hours of purchase. Please contact me if you have negative feedback rating. The sale is subject to the following conditions and representations. This vehicle is being sold as is, where is with no warranty in connection therewith. The seller shall not be responsible for the correct description, authenticity, genuineness, or defects herein, and make no warranty in connection therewith. No allowances or set aside will be made on account of any incorrectness, imperfection, defect or damage. Any descriptions or representations are for identification purposes only and are not to be construed as a warranty of any type. It is the responsibility of the buyer to have thoroughly inspected the vehicle, and to have satisfied oneself as to the condition and value based upon that judgment solely. Seller assumes no responsibility for any repairs regardless of any oral statements about the vehicle. |