1970 FORD MUSTANG, MACH 1 428CJ-4SPD- R CODE. "NO RESERVE PRICE"

Condition:	Used
Make:	Ford
Model:	Mustang
SubModel:	R-CODE
Type:	Coupe
Trim:	MACH 1
Year:	1970
Color:	Orange
Engine:	428 COBRA JET
Cylinders:	8
Transmission:	Manual
Drive type:	RWD
Interior color:	Red
Vehicle Title:	Clear
Item location:	Thousand Oaks, California, United States

Extras

Listed by

Private seller

Enquire

Description of 1970 Ford Mustang R-CODE

1970 Ford Mustang Mach 1, Calypso Coral paint & Vermilion Interior. 428 cobra Jet, 4spd, with very desirable options check the Deluxe Marti report for details.The engine is a 1968 Ford 428CJ that is bored .20 over and is professionally built to make aprox 450 HP.The engine has 0 miles on it, it has just been test ran to be broken in.the carburetor is a Quick Fuel 750 double pump. Pertronix electronic ignition system. The Ford Top Loader Transmission was custom built, wide ratio and custom short throw threaded shift rods.Correct Hurst shifter and T- handle.New performance flywheel and clutch assembly.Easy clutch pedal.The rear end is a Ford N case 9" Traction lock with 3.50 gear ratio.large spline axles. The rear end was professionally assembled ( I can not verify that, other then the axles). All Brakes lines, master cylinder, power booster, rotor, drums, calipers and e brake cables replaced ( the lower bracket needs to be welded to the floor pan).Custom aluminium Radiator that has been black Thermo-Coated. Additional pictures can be provided. Money spent on parts from Mansfield Mustang $3,131.00. NPD $1,425.00. Summit Racing $1279.00 . Additional invoices that total more the $10,000.00 in parts. Rare Factory vermilion Door Panel, all seats have been redone. Factory seat belts, restored trunk door, correctly restored center counsel, new reproduction dash & interior panels, new head liner, new carpet kit inbox, new front Carlite tinted windshield, heat / sound insulation extra roll included.Restored factory rear louvers (needs hardware), Factory rear spoiler (needs pedestals, paint). new custom concourse correct drive shaft made in the USA (does have modern grease-able u-joints) Restored 1970 air cleaner Shaker assembly (extra- mid plate) with Snorkel. NOS or restored correct dual point distributor(difficult to find & expensive) . Restored correct Ford radiator cooling fan (difficult to find & expensive). extra cooling flex fans provided. New Magnaflow stainless exhaust system.
The vehicle will need to be completed, Missing bumpers & brackets, side windows can be restored or replaced. Driver side window and Passenger side do not match one is Tinted. VERY IMPORTANT, the engine fitment is extremely tight due to the factory steel reinforcement on shock towers.The custom exhaust headers in the engine picture were removed and new Thermo-Coated exhaust manifolds installed.The engine still has minimal side clearance and additional adjustments should be made.Total Control engine mounts have been installed (new replacement factory mounts included) Passenger side door does not line up that great to quarter panel.all body panels need to be lined up, fenders not totally secured ( VIN stamped on both fender aprons under front fenders).
It appears that the rear quarter panels and the floor was replaced before I purchased the vehicle.
This Mustang will be very rare and desirable when completed.
E-mail me with any questions, Please check the You Tube link below showing the fresh engine running.
https://youtu.be/tI01_nIAhdE?t=2s
Here is some more information on the engine. 1967 428 CJ block (possibly from a Shelby Mustang) that was freshly bored .20 over, oil gallerys modified & the block was deburred. Probe forged flat top pistons 10 to 1 compression, total seal rings, factory CJ rods were magnafluxe, resized and ARP bolts. The stock crank has been machined & the entire rotating assembly was professionally balanced from the harmonic balancer to the flywheel. The heads are 1969 CJ heads that have had the normal rebuild including valves, seats, guides and surfacing. The engine retains the stock valve train with the addition of Isky double coil valve springs to accommodate the Erson hydraulic flat tappet camshaft (296 duration / 551 lift -3000 to 6000 rpm). The engine was professional assembled by Mark DeGroff's machine shop. The factory intake manifold has been matched to the head ports (FE intake manifolds and heads must meet correctly for the valve covers to line up). I have personally build several Ford Engines but I decided to have Mark do this one for me since he performed all the Machine work and is very experienced with Fords and there idiosyncrasies.

I am going to include the Ford 4 SPD Top Loader transmission that came with the car ( its highly race modified) it does have the correct case but the tail section is longer then the Mustang application & is not particularly clean. I decided to just keep it and have another one custom built for the car. Another center counsel ( needs to be restored) and of course the instrument cluster with the factory Tachometer and clock are included.The Steering wheel included is a 1970 Rim Blow that needs to be restored.The body rocker molding is included as well. I also am going to include a custom radiator over flow tank & vacuum canister to assist Power Brakes to deal with the performance Cam Shaft.