1966 FORD MUSTANG 289 V8 COUPE TRANS AM BARN FIND 1965 65 66

Condition:	Used
Make:	Ford
Model:	Mustang
Type:	Coupe
Year:	1966
Mileage:	45000
VIN:	6F07T309XXX
Color:	Red
Engine:	289
Cylinders:	8
Transmission:	Automatic
Drive type:	RWD
Interior color:	Black
Vehicle Title:	Clean
Item location:	Robins, Iowa, United States

Extras

Listed by

Private seller

Enquire

Description of 1966 Ford Mustang

1966 Ford Mustang coupe, originally a 6 cylinder manual car. I was building a Trans Am style race car, hoping to have done by now, but have too many other projects piling up to finish it. The car has a pretty solid foundation to build, had new floors installed when I got it. I had another 66 coupe that we did a complete restomod on, so all the V8 drivetrain was saved for this one. It got the 8" rear axle that was gone through, V8 driveshaft with new u-joints, rebuilt C4 transmission with the correct crossmember for the parking brake, T-handle shifter and linkage (all already installed in the car), and the 289 V8 engine. The engine has been rebuilt, probably has less than 2,000 miles on it, and runs smooth. It has a new fuel pump, Edelbrock intake, chrome valve covers and air cleaner, new Autolite plugs, wires, cap and rotor, new water pump, and a new Powermaster alternator (still in the box). It has a Holley 4bbl carb- may need gone through as was sitting on the shelf for awhile. The front suspension has been swapped to the correct V8 components and new shocks front and rear installed. All new brakes, wheel cylinders, new steel brake lines, all new rubber brake hoses, and new '67 dual master cylinder installed. The manual pedal setup was swapped out for the correct automatic brake pedal. New steel fuel line from rear to front. New BFG white letter tires on 1972 Mustang Ralley wheels. Complete dual exhaust system with 2 1/4" pipes. New radiator, new upper and lower rad hoses, new coolant lines to the heater box. I used 1972 Mustang front bucket seats with the high backs- still have the original '66 seats and will trade out if preferred. New Speedway 22 circuit fuse block and wiring harness has been installed- block and headlight circuits are in, leads are run to new ignition switch, radio, and cluster but need to be connected yet. Taillight lead has also been run, but still needs connected. The original removed wiring harness is included in case any pigtails are needed, along with several other parts as seen in the pics. I replaced the door hinges on the driver's door, as well as the regulator that was stuck. All other glass is in good usable shape, windows roll up and down freely.I was going for a 'barn fresh' trans am style race car with this project and planned on painting the hood and fender tops a flat black, as well as faded numbers on the doors. It basically has all new drivetrain, brakes, suspension, and steering, with a worn out patina on the outside. It's to the point where it needs very little to be a running car, so a great project start! I'd finish it myself, but have to make room for other projects coming back from paint this month. My loss your gain, right? Any questions please feel free to ask me. Sold as is, $500 deposit due within 24hrs of end of auction, remainder due within 7 days. Buyer to contact me asap to arrange pick up of the car. I can store it for longer if needed provided it's paid in full in advance. Serious bidders only please- if you have 1 or less feedback, contact me before bidding or your bid will be rejected and blocked. Thanks for looking, and good luck bidding.

On Mar-02-20 at 05:22:39 PST, seller added the following information:

To answer a couple questions; the engine does have a new starter installed, there's a new voltage regulator installed, and the parking brake is completely installed from the cables to the equalizer bar and pull handle under the dash (will probably need adjusted yet). Yes, I water tested the cowls and they do not leak. I do have the missing trim from the base of the windshield- in good shape and it is included.The car rolls and steers perfectly as the front suspension is all connected and tight, no issues loading it.The Speedway wiring kit is mostly installed, and is a really nice kit. The wires are marked every foot, and the detailed instructions are included as well as all the connectors that came with it. It has new wiring for the battery and alternator as well.

On Mar-02-20 at 06:27:31 PST, seller added the following information:

I thought I posted this answer so all could see it, but it didn't come through; What will it take to get it running? From where it sits now, to run it would need the wiring finished, fuel line from new pump to carb installed (carb may or may not need cleaned or sealed as it's been sitting on a shelf) and connected, the new alternator installed, the new radiator hoses connected, fluids checked/filled, a battery and cables. There may be a few minor miscellaneous items, but I think everything else is there and installed already, so just a little time on your part.