1940 Willys blown Hemi Gasser

Condition:	Used
Make:	Willys
Model:	440
SubModel:	gasser
Type:	Coupe
Trim:	HEMI
Year:	1940
Mileage:	31
Color:	Red
Engine:	hemi
Cylinders:	8
Fuel:	Gasoline
Transmission:	Automatic
Drive type:	RWD
Interior color:	Black
Safety:	seat belts , roll cage
Vehicle Title:	Clear
Item location:	Grant, Florida, United States

Extras

Listed by

Private seller

Enquire

Description of 1940 Willys 440 HEMI

Listing for a friend,
This is a good running street gasse, registered and titled in my name as a 1940 Willys coupe using the original 40 VIN tag on a 40 Willys chassi, with a 41 center section . Completely street lega, everything is new or rebuilt . It rides like a Gasser .
This started as a wrecked Willys Gasser Coupe I found in Maine, The car was crashed bad to the point the rear of the roof was ripped off. So i rebuilt the body shell with a piece from a fiberglass body I had . The back half of the roof is from the glass car everything else is steel. The fenders front and rear are stee, hoo, center section,trunk lid is stee, the doors i made from sedan doors and are steel also . Grill and headlights are original not aftermarket .The floors are made from steel sheet metal .

The chassis is a mint 40 Willys chassis sand blasted and painted flat black. All new springs and chassis parts were used with a WAC custom built front axle . Ford spindles and disc brakes on the front . The 57 olds rear axle is all new rebuilt Posi 30, 31 spline axles and brakes . Vintage Cragar SS wheels front and rear with new cheater slicks and skinny front runners.

The interior is a set of buckets from Summi, they are new and comfortable . Tuck n roll door panel, kick panels and behind the seat, headliner is roughed in place . Series 60 B&M shifte, old SW gauge, seat belt, 4 point cag, functional gas pedal from an old drum se, yes it is what you use to wack the throttle . All new tinted glass and channels rubbers etc .
The motor is a 331 HEM, had it bored to 3.98 , sonic tested the bloc, new 7.5:1 Venoila blower pistons and used new Childs and Albert aluminum rods spinning on a 5/8 stroked crank you have a 421 CU IN HEMI . The motor uses studs top and botto, oil pump was ported and polishe, I run the blower at 5 over to keep it from heating up in the florida heat .. The motor is full of all the best parts from hot heads . The Triple 5 heads have stainless valve, spring, blower ca, hyd. lifter, from hot head, HH timing cove, BBCH water pum, hidden alternato, MSD electronic dizzy with a bo, 671 supercharger w/ 2 500 cfm carter/edelbrock carb, MPH scoo, patina chrome valve covers.
The custom made 2.5 " fender well headers are HPC coated back in the late eighties and still look top notch .I attached the motor to a fresh 2 spd powerglid, reverse valve body race ready transmission with a 2500 stall converter and again to a POSI olds /pontiac rear .
Took about a year or more full time to put it togethe, I have been building cars for over 40 year, know what i am doing as this is Willys number 21 .

Will sell to international buyer, you will need to make all shipping arrangement, do a wire transfer for payment and are welcome to have someone come and inspect the car prior to sale .
Don't need the mone, space or excuse, looking for a serious buyer . Trades never work so NO TRADE, cash or bank wire only accepted .Shoot me a number and time to reach you at if you want to talk about the car.