Real 1932 Model B Ford Pickup Truck *PROJECT* (New Package Details & Price!)

NOTE: If you've been searching for a Model B truck project in the past few months, you may REMEMBER this item/listing! Due to some changes in circumstance, I have taken over ownership (from my Father) and responsibility for this truck's sale. Below are all the details I had collected from him....everything we could think of! READ CAREFULLY what items are included in THIS, current listing!!

* * IMPORTANT NOTE to "PREVIOUS" WATCHERS * *

Based on the feedback of multiple potential buyers, we have decided toEXCLUDE the host of mechanical components and extra partsthat were formerly included in this bulk, project sale. This was in order to make for EASIER SHIPPING and a LOWER PRICE for you!

>> If you are interested in MORE or DIFFERENT parts, please just ASK!! Together we will work out a fair price adjustment.

>> If you want a LOWER price, we can discuss what parts you do NOT need that can be left out to save you $$.

* * Please just aim to be reasonable and fair in your requests * *

**This package is located in the garage at my father's house in WEST VIRGINIA.** This is where you'll pick up the vehicle!

Please submit ALL QUESTIONS/OFFERS to me (Rachel) here, through the eBay messaging system. If you have a very specific, technical question that I can't answer easily, please allow me 24 hours to retrievea more precise answer from Dad. I will reply to your message thread ASAP! If further discussion is required, we can speak on the phone as needed.

Thanks so much for LOOKING!!

~ ~ ~~ ~ ~ ~ ~ ~~ ~ ~ ~ ~ ~ ~

CURRENTPRICE: $11,500.00 (formerly $14,500 with lots of mechanical parts included)

Items/StructuresINCLUDED in this 1932 Ford Truck Project PACKAGE:

• Frame
• Front Grill(including radiator)
• Cab
• Chassis
• Bed (and bed sides)
• Sheet metal (hood, grill,Fenders front and back etc.) " NOT PICTURED"
• Front axle
• Wishbones and spring
• and a host of “small parts” (window regulators, door handles, trim. dash board) (ONLY included at full price)
  

Item NOT INCLUDED but available for swap-out or Add-on, if interested, as per your request:

clutch, trans, rear end housing, center section, drive shaft, rear suspension, brakes, seats, etc. (engine NOT included nor available)

~~~~~~~~~~~~~~~~~~~~~~~

DETAILS & DESCRIPTIONS

VEHICLE DESCRIPTION

This is it! A real deal, all steel, '32 Model B Ford pickup. These beauties are getting impossible to find!

* * *Let's be clear....this is being sold as a PROJECT / collection of parts !!! * * *It does not "roll" yet and does not drive.

This was a build near and dear to my Dad's heart....the ULTIMATE HOT ROD....that he had been pecking away at for years. Unfortunately, my mom's health issues forces the sale of this package.

This is your opportunity to pick up where he left off, have a blast building your own custom creation and potentially lucrative investment!! (Do a little research and you'll see what these trucks go for, completed!)

Speaking of which...below, you'll see the background of the work Das had already completed. It's important to note that *HE* was the builder and personally performed all of the work listed. He isa retired NASCAR cup series mechanic, engine-builder, welder and fabricator. (I say that not to boast, but so that you have confidence in the quality of the work completed.) So go ahead and build an "old school" hot rod or something different.... because almost all the really important original components are HERE!

DETAILS OF STRUCTURAL COMPONENTS & FABRICATIONS:

• Starting with the very solid stock Frame, the front crossmember was removed and replaced with a model A crossmember, to lower the ride height.
• The original K member was removed and the frame rails were boxed.
• Then a custom fabricated tubular cross member was grafted in.
• The stock wishbone was split and motor and trans mounts were added to carry a small block Chevy and a super T-10 four speed.
• The front axle has been relocated "Spencer style" to ride in front of the spring, to further lower the ride height, and stretching the wheel base an extra 3 in.
• Next the cab was taken to bare metal, and then treated to a 4-inch chop.
• All of the wood, cab stiffeners and the floor boards have been replaced with steel.
• The doors, windshield frame, garnish moldings, have been chopped to match and metal finished, so the hard work is done!

INCLUDEDPARTS & COMPONENTS: **READ CAREFULLY **

• Many of the impossible to find small parts are included like: window regulators, door latches, garnish moldings and trim. These are INCLUDED for you! (but can be left out if you're trying to save $)
• The grill is the correct "commercial" grill (not from a passenger car, which is different)
• The plan was to run without a hood, but a perfect hood is also included!
• A genuine '32 Bed with excellent sides is also included. These beds, are a one year piece as the '33-'34 trucks had a longer (112in.) wheel base, and won't fit a '32, making it a very rare part. (SEE IMAGES for details!)
• NOTES on the BED: “Ford built their beds differently than Chevrolet or Dodge. There is wood in the bed but you can't see it, it had a steel “floor” over it and the wood is underneath for support. On this truck the wood and metal " floor" need to be replaced. But since anyone building a hot rod style truck would shorten the bed those parts would get replaced anyway. The only parts that are important are the bed sides, headboard and tail gate. Of which the parts that I have are in good condition.
• The Ford pickups with fancy wood beds (that people see in car shows and magazine pictures) are " kits" that company's sell. It is not the way these trucks came from the factory. The bed frame has to be modified to make it work, although it is fairly simple to do.
• SEE IMAGE - of the sub rails and floor. It has some rust and slight damage but is repairable or would make a good " template.
• SEE IMAGE - of the tailgate and head board

AndYES this truck has a TITLE....It's good/clean. Happens to be from Michigan.Also (FYI) Dad explained to me that these old truck didn't have a VIN sticker like modern cars....they had a number stamped into the frame. So this title is for/matching this exact frame (cab too.) So it's all matching.

So as you see, the majority of the "hard work" is done - but not so much that you couldn't take the project in a new direction and make it your own! (Again, feel free to CONTACT me if you have very specific questions not answered here.)

NOTE: Tons of parts had been collected to go into the project!Many are from NASCAR and the IROC series.There is waytoo muchto list. They are NOT included in this sale!(However, at your request, items can be added-in for a negotiatedprice! Again, just ASK if there's something you need! Otherwise, keep your eyes peeled as in time they will be listed separately on ebay at a later time.

~~~~~~~~~~~~~~~~~~~~~~~~~~

Also keep in mind that "Local Pickup" Is Recommended ... But we can help with out of state buyers!

The truck is on a rolling dolly that goes with the deal if ya want, help with transporting in to a box truck or flat bed. Plus moving it around in a shop, rolls real nice ..

and ought to save you some money on shipping / freight / transport.

However, we are happy to make provisions for packing up the truck in accordance with the requirements for your chosen freight service, should you go that route.
Again, the truck is located in eastern West Virginia- less than 30 minutes outside of Winchester, VA. Easily-accessed off of Route 50.

* * * THANKS for LOOKING!! * * *

~ ~ ~ ~ ~ ~ ~ The "Fine Print" ~ ~ ~ ~ ~ ~ ~ ~

a.) This vehicle and the included parts do NOT carry any Warranty

b.) A NON-REFUNDABLE Deposit is due within 24 hours via PayPal.

c.) Final payment (cash / certified-check or combination thereof) shall be made in-person at pickup, to be executed within 7 days of completion of eBay sale.

d.) NO Refunds, Substitutions, Returns or Exchanges once final written "deal" has been agreed upon in writing on ebay, and sale finalized.